rev 1.1 10/23/00 characteristics subject to change without notice. 1 of 10 www.xicor.com terminal voltages ?v, 32 taps x9313 digitally controlled potentiometer (xdcp ) features solid-state potentiometer 3-wire serial interface 32 wiper tap points wiper position stored in nonvolatile memory and recalled on power-up 31 resistive elements temperature compensated end to end resistance range ?20% terminal voltages, ?v to +5v low power cmos ? cc = 3v or 5v active current, 3ma max. standby current, 500? max. high reliability endurance, 100,000 data changes per bit register data retention, 100 years ? total values = 1k ? , 10k ? , 50k ? , 100k ? packages 8-lead soic, msop and dip description the xicor x9313 is a digitally controlled potentiometer (xdcp). the device consists of a resistor array, wiper switches, a control section, and nonvolatile memory. the wiper position is controlled by a 3-wire interface. the potentiometer is implemented by a resistor array composed of 31 resistive elements and a wiper switching network. between each element and at either end are tap points accessible to the wiper terminal. the position of the wiper element is controlled by the cs , u/d , and inc inputs. the position of the wiper can be stored in nonvolatile memory and then be recalled upon a subsequent power-up operation. the device can be used as a three-terminal potentiometer or as a two-terminal variable resistor in a wide variety of applications including: control parameter adjustments signal processing block diagrams 5-bit up/down counter 5-bit nonvolatile memory store and recall control circuitry one of decoder resistor array r h /v h u/d inc cs transfer gates thirty v cc v ss r l /v l r w /v w control and memory up/down (u/d ) increment (inc ) device select (cs ) v cc (supply voltage) v ss (ground) r h /v h r w /v w r l /v l general detailed 0 1 2 28 29 30 31 two a pplication n ote a v a i l a b l e an20 ?an42?3 ?an71 ?an73 ?an88 ?an91?2 ?an99 ?an115 ?an120 ?an124 ?an133 ?an134 ?an135
x9313 characteristics subject to change without notice. 2 of 10 rev 1.1 10/23/00 www.xicor.com pin descriptions r h /v h and r l /v l the high (r h /v h ) and low (r l /v l ) terminals of the x9313 are equivalent to the ?ed terminals of a mechanical potentiometer. the minimum voltage is v ss and the maximum is v cc . the terminology of r l / v l and r h /v h references the relative position of the terminal in relation to wiper movement direction selected by the u/d input and not the voltage potential on the terminal. r w /v w r w /v w is the wiper terminal and is equivalent to the movable terminal of a mechanical potentiometer. the position of the wiper within the array is determined by the control inputs. the wiper terminal series resistance is typically 40 ? at v cc = 5v. up/down (u/d ) the u/d input controls the direction of the wiper movement and whether the counter is incremented or decremented. increment (inc ) the inc input is negative-edge triggered. toggling inc will move the wiper and either increment or decrement the counter in the direction indicated by the logic level on the u/d input. chip select (cs ) the device is selected when the cs input is low. the current counter value is stored in nonvolatile memory when cs is returned high while the inc input is also high. after the store operation is complete the x9313 will be placed in the low power standby mode until the device is selected once again. pin configuration pin names symbol description r h /v h high terminal r w /v w wiper terminal r l /v l low terminal v ss ground v cc supply voltage u/d up/down control input inc increment control input cs chip select control input v cc cs inc u/d r h /v h v ss 1 2 3 4 8 7 6 5 x9313 8-lead dip/soic r l /v l r w /v w v cc cs u/d r h /v h 1 2 3 4 8 7 6 5 x9313 8-lead msop r l /v l r w /v w inc v ss
x9313 characteristics subject to change without notice. 3 of 10 rev 1.1 10/23/00 www.xicor.com principles of operation there are three sections of the x9313: the input control, counter and decode section; the nonvolatile memory; and the resistor array. the input control section operates just like an up/down counter. the output of this counter is decoded to turn on a single electronic switch connecting a point on the resistor array to the wiper output. under the proper conditions the contents of the counter can be stored in nonvolatile memory and retained for future use. the resistor array is comprised of 31 individual resistors connected in series. at either end of the array and between each resistor is an electronic switch that transfers the potential at that point to the wiper. the wiper, when at either ?ed terminal, acts like its mechanical equivalent and does not move beyond the last position. that is, the counter does not wrap around when clocked to either extreme. the electronic switches on the device operate in a ?ake before break mode when the wiper changes tap positions. if the wiper is moved several positions, multiple taps are connected to the wiper for t iw (inc to v w change). the r total value for the device can temporarily be reduced by a signi?ant amount if the wiper is moved several positions. when the device is powered-down, the last wiper position stored will be maintained in the nonvolatile memory. when power is restored, the contents of the memory are recalled and the wiper is set to the value last stored. instructions and programming the inc , u/d and cs inputs control the movement of the wiper along the resistor array. with cs set low the device is selected and enabled to respond to the u/d and inc inputs. high to low transitions on inc will increment or decrement (depending on the state of the u/d input) a seven bit counter. the output of this counter is decoded to select one of thirty two wiper positions along the resistive array. the value of the counter is stored in nonvolatile memory whenever cs transitions high while the inc input is also high. the system may select the x9313, move the wiper and deselect the device without having to store the latest wiper position in nonvolatile memory. after the wiper movement is performed as described above and once the new position is reached, the system must keep inc low while taking cs high. the new wiper position will be maintained until changed by the system or until a power-up/down cycle recalled the previously stored data. this procedure allows the system to always power-up to a preset value stored in nonvolatile memory; then during system operation minor adjustments could be made. the adjustments might be based on user preference, system parameter changes due to temperature drift, etc... the state of u/d may be changed while cs remains low. this allows the host system to enable the device and then move the wiper up and down until the proper trim is attained. mode selection symbol table cs inc u/d mode l h wiper up l l wiper down h x store wiper position h x x standby current l x no store, return to standby waveform inputs outputs must be steady will be steady may change from low to high will change from low to high may change from high to low will change from high to low don? care: changes allowed changing: state not known n/a center line is high impedance
x9313 characteristics subject to change without notice. 4 of 10 rev 1.1 10/23/00 www.xicor.com absolute maximum ratings temperature under bias ....................?5 c to +135 c storage temperature .........................?5? to +150? voltage on cs , inc , u/d , v h , v l and v cc with respect to v ss ......................... ?v to +7v ? v = |v h ? l | x9313z ................................................................... 4v x9313w, x9313u, x9313t ................................... 10v lead temperature (soldering 10 seconds)..........300? i w (10 seconds) .............................................. ?.8ma comment stresses above those listed under ?bsolute maximum ratings may cause permanent damage to the device. this is a stress rating only; functional operation of the device (at these or any other conditions above those listed in the operational sections of this speci?ation) is not implied. exposure to absolute maximum rating conditions for extended periods may affect device reliability. recommended operating conditions temperature min. max. commercial 0? +70? industrial ?0? +85? supply voltage (v cc ) limits x9313 5v ?0% x9313-3 3v to 5.5v potentiometer characteristics (over recommended operating conditions unless otherwise stated.) notes: (1) absolute linearity is utilized to determine actual wiper voltage versus expected voltage = (v w(n) (actual)? w(n) (expected)) = ? ml maximum. (2) relative linearity is a measure of the error in step size between taps = r w(n+1) ?r w(n) + ml] = ?.2 ml. (3) 1 ml = minimum increment = r tot /31. symbol parameter limits test conditions/notes min. typ. max. unit end to end resistance tolerance ?0 % v vh v h terminal voltage ?v +5v v v vl v l terminal voltage ?v +5v v power rating 10 mw r total 10 k ? power rating 16 mw r total = 1 k ? r w wiper resistance 40 100 ? i w = 1ma, v cc = 5v i w wiper current ?.4 ma noise -120 dbv ref: 1khz resolution 3 % absolute linearity (1) ? mi (3) r w(n)(actual) ? w(n)(expected) relative linearity (2) ?.2 mi (3) r w(n+1) ?r w(n)+mi ] r total temperature coefficient ?00 ppm/? ratiometric temperature coefficient ?0 ppm/? c h /c l /c w potentiometer capacitances 10/10/25 pf; see circuit #3
x9313 characteristics subject to change without notice. 5 of 10 rev 1.1 10/23/00 www.xicor.com d.c. operating characteristics (over recommended operating conditions unless otherwise specified.) endurance and data retention notes: (4) typical values are for t a = 25? and nominal supply voltage. (5) this parameter is periodically sampled and not 100% tested. symbol parameter limits unit test conditions min. typ. (4) max. i cc v cc active current 1 3 ma cs = v il , u/d = v il or v ih and inc = 0.4v/2.4v @ max. t cyc i sb standby supply current 200 500 ? cs = v cc ?0.3v, u/d and inc = v ss or v cc ?0.3v i li cs , inc , u/d input leakage current ?0 ? v in = v ss to v cc v ih cs , inc , u/d input high voltage 2 v cc + 1 v v il cs , inc , u/d input low voltage ? 0.8 v c in (5) cs , inc , u/d input capacitance 10 pf v cc = 5v, v in = v ss , t a = 25?, f = 1mhz parameter min. unit minimum endurance 100,000 data changes per bit per register data retention 100 years test circuit #1 test circuit #2 circuit #3 spice macro model test point v w /r w v h /r h v l /r l v s force current vw test point v h /r h v w /r w v l /r l c h c l r w 10pf 10pf r h r l r total c w 25pf a.c. conditions of test a.c. operating characteristics (over recom- mended operating conditions unless otherwise speci- fied) input pulse levels 0v to 3v input rise and fall times 10ns input reference levels 1.5v
x9313 characteristics subject to change without notice. 6 of 10 rev 1.1 10/23/00 www.xicor.com power up and down requirements there are no restrictions on the sequencing of v cc and the voltages applied to the potentiometer pins during power-up or power-down conditions. during power-up, the data sheet parameters for the dcp do not fully apply until 1 millisecond after v cc reaches is ?al value. the v cc ramp spec is always in effect. a.c. timing notes: (6) typical values are for t a = 25? and nominal supply voltage. (7) this parameter is not 100% tested. (8) mi in the a.c. timing diagram refers to the minimum incremental change in the v w output due to a change in the wiper position. symbol parameter limits unit min. typ. (6) max. t cl cs to inc setup 100 ns t ld inc high to u/d change 100 ns t di u/d to inc setup 2.9 ? t ll inc low period 1 s t lh inc high period 1 s t lc inc inactive to cs inactive 1 s t cph cs deselect time (store) 20 ms t cph cs deselect time (no store) 100 ns t iw inc to vw change 1 5 ? t cyc inc cycle time 4 s t r , t f (7) inc input rise and fall time 500 ? t pu (7) power up to wiper stable 5 s t r v cc (7) v cc power-up rate 0.2 50 v/ms t wr store cycle 5 10 ms cs inc u/d v w t ci t il t ih t cyc t id t di t iw mi (8) t ic t cph t f t r 10% 90% 90%
x9313 characteristics subject to change without notice. 7 of 10 rev 1.1 10/23/00 www.xicor.com applications information electronic digitally controlled (xdcp) potentiometers provide three powerful application advantages; (1) the variability and reliability of a solid-state potentiometer, (2) the ?xibility of computer-based digital controls, and (3) the retentivity of nonvolatile memory used for the storage of multiple potentiometer settings or data. basic configurations of electronic potentiometers basic circuits v r v w /r w v r i three terminal potentiometer; variable voltage divider two terminal variable resistor; variable current v h v l cascading techniques buffered reference voltage + +5v r 1 +v ?v v w v ref v out op-07 v w v w /r w +v +v +v x (a) (b) v out = v w /r w noninverting amplifier + v s v o r 2 r 1 v o = (1+r 2 /r 1 )v s lm308a voltage regulator r 1 r 2 i adj v o (reg) = 1.25v (1+r 2 /r 1 )+i adj r 2 v o (reg) v in 317 offset voltage adjustment + v s v o r 2 r 1 100k ? 10k ? 10k ? 10k ? -12v +12v tl072 comparator with hysteresis v ul = {r 1 /(r 1 +r 2 )} v o (max) v ll = {r 1 /(r 1 +r 2 )} v o (min) + v s v o r 2 r 1 } } lt311a +5v ?v (for additional circuits see an115)
x9313 characteristics subject to change without notice. 8 of 10 rev 1.1 10/23/00 www.xicor.com packaging information 0.118 ?0.002 (3.00 ?0.05) 0.040 ?0.002 (1.02 ?0.05) 0.150 (3.81) ref. 0.193 (4.90) 0.030 (0.76) 0.036 (0.91) 0.032 (0.81) 0.007 (0.18) 0.005 (0.13) 0.008 (0.20) 0.004 (0.10) 0.0216 (0.55) 7?typ. r 0.014 (0.36) 0.118 ?0.002 (3.00 ?0.05) 0.012 + 0.006 / -0.002 (0.30 + 0.15 / -0.05) 0.0256 (0.65) typ. 8-lead miniature small outline gull wing package type m note: 1. all dimensions in inches and (millimeters) 0.220" 0.0256" typical 0.025" typical 0.020" typical 8 places footprint ref.
x9313 characteristics subject to change without notice. 9 of 10 rev 1.1 10/23/00 www.xicor.com packaging information 0.150 (3.80) 0.158 (4.00) 0.228 (5.80) 0.244 (6.20) 0.014 (0.35) 0.019 (0.49) pin 1 pin 1 index 0.010 (0.25) 0.020 (0.50) 0.050 (1.27) 0.188 (4.78) 0.197 (5.00) 0.004 (0.19) 0.010 (0.25) 0.053 (1.35) 0.069 (1.75) (4x) 7 0.016 (0.410) 0.037 (0.937) 0.0075 (0.19) 0.010 (0.25) 0?- 8 x 45 8-lead plastic small outline gull wing package type s note: all dimensions in inches (in parentheses in millimeters) 0.250" 0.050"typical 0.050" typical 0.030" typical 8 places footprint
x9313 characteristics subject to change without notice. 10 of 10 limited warranty devices sold by xicor, inc. are covered by the warranty and patent indemni?ation provisions appearing in its terms of sale onl y. xicor, inc. makes no warranty, express, statutory, implied, or by description regarding the information set forth herein or regarding the freedom of the descr ibed devices from patent infringement. xicor, inc. makes no warranty of merchantability or ?ness for any purpose. xicor, inc. reserves the right to discontinue produ ction and change speci?ations and prices at any time and without notice. xicor, inc. assumes no responsibility for the use of any circuitry other than circuitry embodied in a xicor, inc. product. no o ther circuits, patents, or licenses are implied. trademark disclaimer: xicor and the xicor logo are registered trademarks of xicor, inc. autostore, direct write, block lock, serialflash, mps, and xd cp are also trademarks of xicor, inc. all others belong to their respective owners. u.s. patents xicor products are covered by one or more of the following u.s. patents: 4,326,134; 4,393,481; 4,404,475; 4,450,402; 4,486,769; 4,488,060; 4,520,461; 4,533,846; 4,599,706; 4,617,652; 4,668,932; 4,752,912; 4,829,482; 4,874,967; 4,883,976; 4,980,859; 5,012,132; 5,003,197; 5,023,694; 5,084, 667; 5,153,880; 5,153,691; 5,161,137; 5,219,774; 5,270,927; 5,324,676; 5,434,396; 5,544,103; 5,587,573; 5,835,409; 5,977,585. foreign patents and addition al patents pending. life related policy in situations where semiconductor component failure may endanger life, system designers using this product should design the sy stem with appropriate error detection and correction, redundancy and back-up features to prevent such an occurrence. xicor s products are not authorized for use in critical components in life support devices or systems. 1. life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) sup port or sustain life, and whose failure to perform, when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to res ult in a signi?ant injury to the user. 2. a critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. ?icor, inc. 2000 patents pending rev 1.1 10/23/00 www.xicor.com ordering information physical characteristics marking includes manufacturer s trademark resistance value or code date code v cc limits blank = 4.5v to 5.5v 3 = 3v to 5.5v temperature range blank = commercial = 0 c to +70 c i = industrial = ?0 c to +85 c package m = 8-lead msop p = 8-lead plastic dip s = 8-lead soic end to end resistance z = 1k ? w = 10k ? u = 50k ? t = 100k ? x9313x x x x
|
